How to setup your gateway

GATEWAY

PRODUCT DESCRIPTION
The Gateway is an open Linux platform including multiple wireless networks for communication with smart meters, sensors, smart plugs, thermostats etc.
The gateway is modular and can handle many different wireless protocols at the sametime.

PRECAUTIONS
Do not remove product label as it contains important information

GETTING STARTED

Connect the power cable to the Gateway.
Connect the power adapter to a wall socket.
Connect an Ethernet cable from the Gateway to an internet-connected home router.

Powercable

The LEDs on the front panel are turned on when the system is booting .
The LEDs in the Ethernet connector are turned on and the green LED starts flashing indicating data communication.
After approximately 4-5 minutes the application is started and the system is ready to use.

RESETTING
A factory reset is needed to remove abnormal behavior.
STEPS FOR RESETTING
1. Use a pen and hold down the reset button as indicated in the picture.

2 . Release the pen again when the LED on the front panel starts to flash continuously.

3. The system will reboot and after 4-5 minutes the application will be started again

OTHER INFORMATION
Dispose the product proper.ly at the end of life. This is electronic waste which should be recycled.

CE CERTIFICATION
The CE mark affixed to this product confirms its compliance with the European Directives which apply to the product and, in particular, its compliance with the harmonized standards and speci fications .
(€ )-t RoHS

IN ACCORDANCE WITH THE DIRECTIVES
Radio & Telecommunications Terminal Equipment Directive 2014/53/EU
EMC Directive 2014/30/EU
RoHS Directive 2011/65/EU

OTHER CERTIFICATION
ZigBee Home Automation certified
ZigBee Smart Energy Certified

ZigBee
Certified product

FCC STATEMENT
Changes or modifications to the equipment not expressly approved by the party responsible for compliance would void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Pules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
lncrease the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with the FCC RF radiation exposure limits set forth for an
uncontrolled environment. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Pules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2 . this device must accept any interference received. including interference that may cause undesired operation.

IC STATEMENT

This device complies with industry Canada’s Licence-Exempt RSSs. Operation is subject to the following two conditions:
This device may not cause interference. and this device must accept any interference. including interference that may cause undesired operation of the device.

ISED STATEMENT
Innovation. Science and Economic Development Canada ICES-003 Compliance Label CAN ICES-3 (B)/ N MB-3(8)

AT&T CERTIFICATION
The Gateway is certified for use on the AT&T Network.

All rights reserved.
Wattle assumes no responsibility for any errors, which may appear in this manual Furthermore, Wattle reserves the right to alter the hardware. software. and/or specifications detailed herein at any time without notice, and Wattle does not make any commitment to update the information contained herein . All the trademarks listed herein are owned by their respective owners.

Copyright © Wattle

wattle

back to Gateway
newsletter

Subscribe
to our Newsletter

receive exclusive offers and the latest news on our products and services.

  • This field is for validation purposes and should be left unchanged.

We use cookies to give you the best online experience. By agreeing you accept the use of cookies in accordance with our cookie policy.

Privacy Settings

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

These cookies are necessary for the website to function and cannot be switched off in our systems.

In order to use this website we use the following technically required cookies
  • wordpress_test_cookie
  • wordpress_logged_in_
  • wordpress_sec
  • wordpress_instructions_counter

Decline all Services
Accept all Services